DIN Mai haɗin mata don 1/2 ″ Super m RF na USB
7/16 Din connector an tsara shi musamman don tashoshin tushe na waje a cikin tsarin sadarwar wayar hannu (GSM, CDMA, 3G, 4G), yana nuna babban iko, ƙarancin hasara, babban ƙarfin aiki, cikakken aikin hana ruwa da kuma dacewa ga wurare daban-daban. Yana da sauƙi don shigarwa kuma yana ba da haɗin haɗin gwiwa.
Telsto 7/16 Din connectors suna samuwa a cikin jinsi na namiji ko mace tare da 50 Ohm impedance. Ana samun masu haɗin DIN mu na 7/16 a madaidaiciya ko madaidaiciya madaidaiciya, da kuma, 4 rami flange, babban bulkhead, 4 rami panel ko Dutsen ƙananan zaɓuɓɓuka. Waɗannan ƙirar haɗin haɗin 7/16 DIN suna samuwa a cikin manne, ƙugiya ko hanyoyin haɗe-haɗe.
Features Da Fa'idodi
● Ƙananan IMD da ƙananan VSWR suna samar da ingantaccen tsarin aiki.
● Ƙaƙƙarfan ƙira na kai yana tabbatar da sauƙi na shigarwa tare da daidaitattun kayan aikin hannu.
● Gasket ɗin da aka riga aka haɗa yana kare kariya daga ƙura (P67) da ruwa (IP67).
● Phosphor tagulla / Ag plated lambobin sadarwa da Brass / Tri- Alloy plated jikinsu isar da high conductivity da lalata juriya.
Aikace-aikace
● Kayan aiki mara waya
● Tashoshin Gindi
● Kariyar Walƙiya
● Sadarwar Tauraron Dan Adam
● Tsarin Antenna
| Interface | ||||
| Bisa lafazin | Saukewa: IEC60169-4 | |||
| Lantarki | ||||
| Tasirin Halaye | 50ohm ku | |||
| 1 | Yawan Mitar | DC-3GHz | ||
| 2 | VSWR | ≤1.15 | ||
| 3 | Dielectric juriya irin ƙarfin lantarki | ≥2700V RMS, 50Hz, a matakin teku | ||
| 4 | Dielectric Resistance | ≥10000MΩ | ||
| 6 | Tuntuɓi Resistance | Lamba na waje≤1.5mΩ;Tsarin tuntuɓar cibiyar≤0.4mΩ | ||
| 7 | Asarar Shigar (dB) | Kasa da 0.15 | ||
| 8 | PIM3 | ≤-155dBc | ||
| Makanikai | ||||
| 1 | Dorewa | Mating cycles ≥500 | ||
| Material da plating | ||||
| Bayani | Kayan abu | Plating/Ni | ||
| 1 | Jiki | Brass | Tri-alloy | |
| 2 | Insulator | PTFE | - | |
| 3 | Cibiyar gudanarwa | QSn6.5-0.1 | Ag | |
| 4 | Sauran | Brass | Ni | |
| Muhalli | ||||
| 1 | Yanayin Zazzabi | -40 ℃ ~ + 85 ℃ | ||
| 2 | Mai hana ruwa ruwa | IP67 | ||
Taimako:
* High misali inganci
* Mafi m farashin
* Mafi kyawun hanyoyin sadarwa na sadarwa
* Sana'a, abin dogaro da sassauƙa
* Ƙarfin kasuwanci mai ƙarfi na magance matsalolin
* Ma'aikata masu ilimi don mika duk buƙatun asusun ku
Masu alaƙa
Samfura:TEL-DINF.12S-RFC
Bayani
DIN Mai haɗin mata don 1/2 ″ Super m na USB
| Material da Plating | |
| Tuntuɓar cibiyar | Brass / Azurfa Plating |
| Insulator | PTFE |
| Jiki & Mai Gudanarwa | Brass / alloy plated tare da tri-alloy |
| Gasket | Silicon Rubber |
| Halayen Lantarki | |
| Halayen Ƙarfafawa | 50 ohm ku |
| Yawan Mitar | DC ~ 3 GHz |
| Juriya na Insulation | ≥5000MΩ |
| Ƙarfin Dielectric | 2500 V |
| Juriya lamba ta tsakiya | ≤0.4mΩ |
| Juriya na waje | ≤0.2mΩ |
| Asarar Shigarwa | ≤0.15dB@3GHz |
| VSWR | ≤1.08@-3.0GHz |
| Yanayin zafin jiki | -40 ~ 85 ℃ |
| PIM dBc(2×20W) | ≤-160 dBC(2×20W) |
| Mai hana ruwa ruwa | IP67 |
Umarnin shigarwa na N ko 7/16 ko 4310 1/2 ″ super m na USB
Tsarin haɗin haɗi: (Fig1)
A. gaba goro
B. baya goro
C. gasket
Girman raguwa kamar yadda aka nuna ta zane (Fig2), ya kamata a biya hankali yayin tsiri:
1. Ƙarshen ƙarshen madubi na ciki ya kamata a chamfered.
2. Cire ƙazanta irin su ma'aunin jan karfe da burar a saman ƙarshen kebul ɗin.
Haɗa ɓangaren hatimi: Cire ɓangaren hatimin ciki tare da madubin waje na kebul kamar yadda aka nuna ta zane (Fig3).
Haɗa goro na baya (Fig3).
Haɗa goro na gaba da baya ta hanyar dunƙulewa kamar yadda aka nuna ta zane (Figure (5)
1. Kafin yin dunƙule, shafa man shafawa mai mai a kan o-ring.
2. Rike goro na baya da kebul ɗin ba su motsi, Maƙala a jikin babban harsashi a jikin harsashi na baya. Cire babban harsashi na jikin harsashi na baya ta amfani da maƙarƙashiyar biri. An gama haɗuwa.
